Local care · Family business since 1984Engineer visits Monday–Thursday

BROWSE THE QUESTIONS

Dishwashers guidance

Water left inside, poor cleaning and a leaking door tell different stories. Note the point in the cycle and any message on the display.

Find the observation that matches.

137 guides. The titles describe different symptoms, operating stages or enquiry decisions.

Search this type
Dishwashers

A Miele PowerDisk runs out sooner after changing the AutoDos dose

The HG07-W controls can adjust automatic detergent quantity. A deliberate dose increase can shorten disk life, so compare settings before suspecting uncontrolled dispensing.

Read the guide
Dishwashers

A Miele dishwasher is installing RemoteUpdate: when should controls be used?

The HG07-W manual says an installed RemoteUpdate cannot be undone and warns against switching off during installation. Allow the stated process to finish.

Read the guide
Dishwashers

A Miele dishwasher whistles during washing after a detergent change

Miele notes that detergent can contribute to whistling during a programme. A controlled comparison can help separate that observation from a new mechanical noise.

Read the guide
Dishwashers

A Miele dishwasher with a heat accumulator is connected to hot water

For the HG07-W arrangement in the cited manual, the heat-accumulator function is intended for a cold supply and should be disabled with a hot connection.

Read the guide
Dishwashers

A burning or hot electrical smell comes from the dishwasher

An unfamiliar burning smell is a reason to stop the appliance, even if the programme still appears to run normally.

Read the guide
Dishwashers

A dishwasher basket has lost a wheel or comes off its runner

An unstable loaded basket needs attention before it drops, damages crockery or prevents the door from closing correctly.

Read the guide
Dishwashers

A dishwasher spray arm is visibly split or damaged

Visible spray-arm damage should be reported as a component problem, especially if poor cleaning or a door-area leak appeared at the same time.

Read the guide
Dishwashers

A dishwasher tablet is lying undissolved in the tub

A released tablet shows that the dispenser opened, but it does not show that water circulation and programme conditions were adequate.

Read the guide
Dishwashers

A dishwasher water warning appears after plumbing work

The timing of a new warning can help distinguish an installation issue from a fault that developed during normal service.

Read the guide
Dishwashers

A glass has broken inside the dishwasher

Broken glass changes the priority from routine cleaning to avoiding cuts and protecting the appliance from unseen fragments.

Read the guide
Dishwashers

A newly installed Miele dishwasher has an unfamiliar new-appliance smell

Miele describes a manufacturing-related new smell that fades over the first few programmes. Establish whether that description fits the actual smell and circumstances.

Read the guide
Dishwashers

A newly installed dishwasher fails on its first wash

A first-use problem should be assessed with the installation and handover details before it is assumed to be an unrelated component failure.

Read the guide
Dishwashers

A rhythmic knocking starts while the dishwasher is washing

A repeated knock during spraying can have a different cause from a brief sound during filling or draining.

Read the guide
Dishwashers

A small amount of water is visible inside the dishwasher sump

Visible moisture does not always mean a drain fault; the location and extent of the water matter more than its presence.

Read the guide
Dishwashers

AEG AutoSense will not accept the extra options used with a timed programme

AEG's QuickSelect guidance says additional options cannot be added to its Auto programme. The automatic programme makes its own adjustments.

Read the guide
Dishwashers

AEG ComfortLift basket is stuck in its raised position

AEG identifies uneven weight as a possible cause of a ComfortLift basket twisting out of position. Stop forcing it and use the model's illustrated guidance.

Read the guide
Dishwashers

AEG ExtraSilent changes the wash behaviour when quiet operation is selected

AEG describes ExtraSilent as using lower water pressure and restricting option combinations. A quieter sequence should be assessed against the programme's intended load.

Read the guide
Dishwashers

AEG Half-load option cannot be selected

Half-load is an extra setting on supported programmes, so it may be unavailable even though the dishwasher is working normally.

Read the guide
Dishwashers

AEG dishwasher PF warning: check the supply circumstances

AEG uses PF for an out-of-range electrical supply on the dishwashers covered by its guidance, so the warning is not a diagnosis of the wash pump.

Read the guide
Dishwashers

AEG dishwasher door shifts upward while washing

Movement during the wash should be described separately from the planned automatic opening that some models perform near the end.

Read the guide
Dishwashers

AEG dishwasher switches itself off while you are still deciding on a programme

The FFB93807PM manual describes Auto Off after a period without a programme being started. The panel can therefore go dark during an extended pause.

Read the guide
Dishwashers

AEG i40, i41, i43 or i44: water-level warning checks

The four-beep or four-flash family needs the exact product details, an accessible filter check and a record of whether the warning returns.

Read the guide
Dishwashers

AEG i60-family and i70 temperature warnings

A temperature warning can involve the incoming water, heating or sensing, so it should not automatically become an order for a new heater.

Read the guide
Dishwashers

AEG i80 with AirDry: record whether the door attempted to open

When the model's guidance links i80 to automatic door opening, distinguish a disabled feature from an opening mechanism that cannot complete its action.

Read the guide
Dishwashers

AEG iC0 and i90 families: keep the complete control warning

Similar-looking electronic warnings can have different manufacturer restart instructions, so preserve the exact characters before changing anything.

Read the guide
Dishwashers

AEG salt and rinse-aid refill indicators disappear while a programme runs

AEG's indicator guidance says these refill lights remain off during a running programme. Their temporary disappearance is not a confirmation that a reservoir has refilled itself.

Read the guide
Dishwashers

Alexa says the Miele dishwasher needs salt, but its refill light is off

Miele's Alexa refill notification is not a live reading of the dishwasher's refill indicators. Check the appliance before adding more product.

Read the guide
Dishwashers

An AEG 30-minute programme cleans lightly soiled dishes but leaves them wet

AEG's programme guidance describes its 30-minute wash without a drying phase. A short wash can therefore finish without providing the result expected from a full wash-and-dry cycle.

Read the guide
Dishwashers

AutoDos is inactive during the Miele Maintenance programme

The HG07-W Maintenance programme is intended for appliance care, and its instructions deactivate automatic detergent dispensing for that sequence.

Read the guide
Dishwashers

Bosch Auto programme: when sensor sensitivity matters

A persistent change in automatic washing performance may justify checking the model's sensitivity setting alongside the detergent and load.

Read the guide
Dishwashers

Bosch Extra Clean Zone: cleaning the upper-basket jets

The small Extra Clean Zone assembly needs its own inspection when dishes placed above it repeatedly emerge with residue.

Read the guide
Dishwashers

Bosch Favourite button no longer selects the expected wash

A saved Favourite can replace the factory pre-rinse setting, so a changed selection does not necessarily mean the controls are faulty.

Read the guide
Dishwashers

Bosch Machine Care: why cleaner placement matters

On the SMD6ZCX60G, the maintenance programme has two cleaning phases with different product positions.

Read the guide
Dishwashers

Bosch TimeLight projection disappeared after kitchen work

A running dishwasher can lose its visible floor display when a plinth or cabinet arrangement interrupts the projection.

Read the guide
Dishwashers

Bosch Zeolith drying: keeping the air openings clear

A pan or plastic box placed beside a drying outlet can affect a Bosch dishwasher even when both spray arms turn freely.

Read the guide
Dishwashers

Bosch baking-sheet spray head: when the top basket is removed

Removing an upper basket to fit oven trays requires the designated spray-head arrangement on models that support it.

Read the guide
Dishwashers

Bosch dishwasher occasionally uses extra time and water

Water-softener regeneration can add an intermittent step even when the same programme and load size are selected.

Read the guide
Dishwashers

Bosch dishwasher starts on Eco instead of the last programme

A startup preference can explain why the controls return to Eco each time the appliance is switched on.

Read the guide
Dishwashers

Bosch push-open dishwasher door needs two presses

Some handleless Bosch models intentionally require a double press when their electric childproof door setting is enabled.

Read the guide
Dishwashers

Bosch remote start stops working after a dish is added

Opening the door can cancel a one-time remote-start permission while leaving the dishwasher connected to the app.

Read the guide
Dishwashers

Bosch upper basket sits crooked after a height adjustment

If one side of an adjustable basket has dropped, restore matching height settings before judging the rails or door clearance.

Read the guide
Dishwashers

Can delicate glasses and heavily soiled pans share one dishwasher load?

A mixed load can demand conflicting programme conditions, so the care limits of the most delicate items matter.

Read the guide
Dishwashers

Can the Miele SolarSave programme work from an ordinary cold supply?

SolarSave in the cited HG07-W manual operates without appliance heating and requires a suitable hot-water connection. Its name should not be treated as a universal economy option.

Read the guide
Dishwashers

Choosing a replacement cutlery basket or tray for a dishwasher

A replacement accessory needs to fit the model and preserve the spray paths, loading clearance and safe support of utensils.

Read the guide
Dishwashers

Choosing between dishwasher cleaning and descaling

Greasy residue and mineral deposits are different maintenance concerns, so the product should match the problem and the model instructions.

Read the guide
Dishwashers

Clean-looking dishes come out covered in gritty specks

Fine particles on otherwise washed items can be redeposited material, so their distribution and the accessible filter condition are worth recording.

Read the guide
Dishwashers

Comparing dishwasher repair with replacement

A useful comparison includes the confirmed fault, fitting requirements and full costs, rather than a product price alone.

Read the guide
Dishwashers

DishDrawer Knock to Pause misses taps or pauses unexpectedly

The knock sensor and the drawer lock perform different functions, so use the action specified for the operating stage.

Read the guide
Dishwashers

DishDrawer fan restarts when a clean drawer is closed

An integrated DishDrawer can resume its drying fan after unloading even though no new wash has been selected.

Read the guide
Dishwashers

Dishes feel greasy after the dishwasher has finished

Grease remaining across a load calls for a review of programme suitability, detergent and recent washing performance.

Read the guide
Dishwashers

Dishes retain an unusual detergent smell after washing

A changed smell should prompt a review of product use and rinsing performance, without tasting residues to identify them.

Read the guide
Dishwashers

Dishwasher buttons do not respond while a lock symbol is shown

A control lock can prevent ordinary button changes without indicating an electronic failure or a jammed physical door.

Read the guide
Dishwashers

Dishwasher glass damage: scratches and cracks versus a film

Visible scratches, chips or cracks need a loading and programme review; adding more cleaner will not restore a damaged glass surface.

Read the guide
Dishwashers

Dishwasher results deteriorated after changing detergent

A clear product-change date can help isolate a washing problem without immediately attributing it to a failed component.

Read the guide
Dishwashers

Dishwasher water disappears, then returns while it is idle

Water returning hours after a successful drain is useful evidence about when and where the unwanted water enters.

Read the guide
Dishwashers

Do combination dishwasher tablets replace separate rinse aid?

The answer depends on the appliance instructions and results, rather than assuming every combination tablet behaves identically in every machine.

Read the guide
Dishwashers

Does a food-safe symbol mean an item can go in the dishwasher?

Food-contact suitability and dishwasher suitability are different claims, so check the item’s care information before loading it.

Read the guide
Dishwashers

Fisher & Paykel DishDrawer U4: inspect the other drawer's display

On the DishDrawer generation covered by Fisher & Paykel's cited guide, U4 directs attention to a fault reported by the other drawer.

Read the guide
Dishwashers

Foam fills the dishwasher after the wrong cleaning product was used

Excess foam needs a controlled response, particularly if hand-washing liquid or another unsuitable cleaner entered the machine.

Read the guide
Dishwashers

Glasses have rainbow streaks after the dishwasher cycle

Streaking that appears after a product or dosing change is useful evidence and should not automatically be treated as hard-water scale.

Read the guide
Dishwashers

Glasses look cloudy after washing: residue or lasting surface damage?

Cloudiness should be described before stronger cleaning is attempted, because removable deposits and damaged glass need different decisions.

Read the guide
Dishwashers

Lipstick remains on cup rims after dishwashing

A resistant mark around a drinking rim calls for a different comparison from a load that is generally covered in food residue.

Read the guide
Dishwashers

Loading heavy cookware into an AEG ComfortLift basket

The FFB93807PM manual gives an 18 kg maximum basket load and warns against excessive pressure. Check the limit for your exact model before loading heavy cookware.

Read the guide
Dishwashers

Miele AutoDos F600: identify the dispensing system before cleaning it

F600 concerns the AutoDos dispensing outlet. The owner cleaning method differs between AutoDos generations, so establish the fitted version first.

Read the guide
Dishwashers

Miele AutoDos F601: can the dishwasher use its ordinary detergent compartment?

Miele provides a manual-dispensing option for an unresolved F601 on applicable AutoDos models. Confirm the exact fault before using that route.

Read the guide
Dishwashers

Miele BrilliantLight switches off while the dishwasher door is still open

The HG07-W manual describes an automatic lighting timeout. A lamp going out during prolonged loading or cleaning may be following that setting.

Read the guide
Dishwashers

Miele Check filters reminder: maintenance prompt or breakdown?

The Check filters message can be a scheduled reminder. Its appearance alone does not show that a sensor has found a blocked filter.

Read the guide
Dishwashers

Miele Close salt reservoir lid message after a refill

This message asks you to check the reservoir closure. It should not be treated as a request to add another measure of salt.

Read the guide
Dishwashers

Miele EcoFeedback shows different figures before and after a wash

EcoFeedback distinguishes a programme estimate, measured programme consumption and accumulated totals. Comparing different kinds of figure can make normal information look inconsistent.

Read the guide
Dishwashers

Miele F14 or F78 after months without use: report the disuse history

Miele's guidance for these circulation-related faults includes pumps sticking after long inactivity. The same codes can also require technical assessment.

Read the guide
Dishwashers

Miele F607: why lower spray-arm clearance matters to AutoDos

F607 can switch off automatic dispensing because the lower spray cannot properly flush the AutoDos outlet. Loading becomes part of the investigation.

Read the guide
Dishwashers

Miele F70 with the drain pump running: respond to the Waterproof warning

F70 identifies activation of Miele's Waterproof system. Its response differs from ordinary water left in the tub after a wash.

Read the guide
Dishwashers

Miele Glasses programme leaves beer glasses wet without a normal drying phase

The special Glasses programme in the cited HG07-W manual omits rinse aid and drying. Its intended result differs from an ordinary mixed-load programme.

Read the guide
Dishwashers

Miele dishwasher consumption readings increased after a software update

Miele reports that water and electricity consumption can rise temporarily after an update. Compare several ordinary washes before interpreting an isolated change.

Read the guide
Dishwashers

Miele dishwasher says Waiting for SmartStart instead of starting immediately

SmartStart can wait for an external energy-management signal within a chosen time frame. This differs from a programme that has failed to begin washing.

Read the guide
Dishwashers

Miele dishwasher shows a logo or rolling zero before buttons respond

A brief startup pause can occur as a Miele dishwasher leaves standby. Repeatedly pressing its controls can make that normal sequence harder to recognise.

Read the guide
Dishwashers

Miele recommends a high-temperature programme after frequent cooler washes

The Hygiene cycle reminder on relevant HG07-W controls relates to the recent programme routine. It is not an error code naming a broken component.

Read the guide
Dishwashers

Miele time display flashes after the automatically opened door was pushed shut

On applicable models, the door catch may not reset if an AutoOpen opening was cut short. Fully opening the door can be the missing step.

Read the guide
Dishwashers

Miele washes use extra water after enabling a second interim rinse

The second-interim-rinse setting can persist across eligible programmes. It should be reviewed when a deliberate rinsing change remains active longer than intended.

Read the guide
Dishwashers

More AEG QuickSelect ECO bars are lit: is consumption higher or lower?

AEG's QuickSelect guidance uses more illuminated ECO bars to indicate lower consumption. The graphic should not be read like a power-level display.

Read the guide
Dishwashers

New flooring prevents the dishwasher from being pulled out for service

A raised floor or fixed plinth can change repair access, even though the dishwasher remains in its original position.

Read the guide
Dishwashers

One dishwasher basket washes well while the other stays dirty

Uneven results across the baskets can reveal a distribution or loading problem that is hidden by a general description of poor cleaning.

Read the guide
Dishwashers

Opening an AEG dishwasher during drying can end the programme

The FFB93807PM manual describes a drying-phase interruption rule that differs from ordinary mid-wash pausing. Opening the door may therefore change the final sequence.

Read the guide
Dishwashers

Plastic containers remain wet while plates and glasses are dry

A drying difference between materials is not the same evidence as the entire dishwasher load remaining cold and wet.

Read the guide
Dishwashers

Preparing a dishwasher fault report in a rented home

A clear technical report and an agreed contact for access and payment help arrange the visit without mixing fault diagnosis with administrative questions.

Read the guide
Dishwashers

Preparing an AEG ComfortLift dishwasher for filter cleaning

The FFB93807PM care instructions require the lift basket to be empty and locked in the raised position. Establish that safe arrangement before reaching the filter area.

Read the guide
Dishwashers

QuickPowerWash cleans poorly while a longer Miele programme works

A short programme gives detergent less time to dissolve. Miele specifically advises using detergent suitable for QuickPowerWash when results differ between programmes.

Read the guide
Dishwashers

QuickPowerWash has finished but the Miele door has not opened yet

On the Miele programme described in its support guidance, AutoOpen follows a drying delay after the countdown finishes. Zero time does not mean the door must move immediately.

Read the guide
Dishwashers

Removing a previous owner's Miele dishwasher network connection

A used connected dishwasher needs its network configuration reviewed. Miele's HG07-W instructions specifically address resetting network settings when ownership changes.

Read the guide
Dishwashers

Removing the upper basket for Miele Tall items: use the dedicated programme instructions

The Tall items programme on the cited HG07-W model permits a specific basket arrangement for large heat-resistant cookware. That arrangement should not be copied into unrelated programmes.

Read the guide
Dishwashers

Reporting a dishwasher error code without guessing the failed part

A code needs the exact appliance identity and operating context; the same characters can mean different things across brands and models.

Read the guide
Dishwashers

Returning a dishwasher to use after a long period idle

An appliance left unused needs a visible condition check and its shutdown history before a normal load is started.

Read the guide
Dishwashers

Reviewing dishwasher hardness settings after a water-supply change

A moved appliance or changed household water treatment can make an old softener setting inappropriate without proving the dishwasher is faulty.

Read the guide
Dishwashers

Rinse aid needs refilling unusually often: inspect the dispenser-lid seal

On Miele combination dispensers covered by its guidance, a loose or missing rinse-aid lid seal can explain unusually frequent refills.

Read the guide
Dishwashers

Rust-coloured spots appear on cutlery after dishwashing

Spots on cutlery do not by themselves establish that the stainless dishwasher tub is rusting.

Read the guide
Dishwashers

Setting Miele EcoStart when electricity tariff periods have changed

EcoStart uses saved tariff windows and priorities on compatible Miele controls. An outdated window can make its timing unsuitable even when the dishwasher works normally.

Read the guide
Dishwashers

Tea stains remain in mugs although the rest of the load is clean

Stubborn staining on a few mugs is a more specific problem than a dishwasher failing to wash the whole load.

Read the guide
Dishwashers

The Express extra is unavailable with a selected Miele programme

Programme extras have compatibility rules on the HG07-W controls. A greyed-out option can be an intentional restriction rather than an unresponsive touchscreen.

Read the guide
Dishwashers

The Miele AutoOpen door rail stays extended after opening

An opening rail that does not retract deserves a mechanical report. Changing the programme or forcing the door closed is not an appropriate substitute.

Read the guide
Dishwashers

The Miele app can show dishwasher status but cannot start a wash

Remote viewing and remote control are separate functions on compatible Miele dishwashers. An available status screen does not establish that remote starting is enabled.

Read the guide
Dishwashers

The Miele dishwasher displays or sounds an alert from another appliance

SuperVision can show other connected Miele appliances on an equipped dishwasher. The source of an alert therefore matters before a repair is booked.

Read the guide
Dishwashers

The Miele dishwasher drains stored water while apparently switched off

Some Miele HG07-W models automatically empty their heat accumulator after prolonged disuse. The display may remain dark during this planned procedure.

Read the guide
Dishwashers

The Miele dishwasher menus changed to a language you cannot read

The HG07-W manual uses a flag marker beside its language menu. That visual cue helps restore a readable interface without resetting unrelated settings.

Read the guide
Dishwashers

The dishwasher appears idle because delayed start is selected

A clock symbol or countdown may describe a scheduled start rather than the remaining wash time.

Read the guide
Dishwashers

The dishwasher baskets or cabinet have changed colour without rust damage

Miele identifies a combination of light soiling, high temperatures and multicomponent tablets as one cause of cabinet or basket discolouration.

Read the guide
Dishwashers

The dishwasher detergent lid will not click shut before a wash

A lid that cannot close before starting needs a different check from a tablet left behind after washing. Residue can obstruct the catch.

Read the guide
Dishwashers

The dishwasher dishes are dry but the inner door still has a damp film

Miele describes residual moisture on the inner door and cabinet walls as part of its drying process. The location of the moisture matters.

Read the guide
Dishwashers

The dishwasher display lights up but the programme will not begin

A lit display shows that some power is present; it does not confirm that the door, controls and water conditions permit a start.

Read the guide
Dishwashers

The dishwasher door opens automatically near the end of a wash

Automatic opening can be a model feature, but a new or uncontrolled opening needs checking against the appliance instructions.

Read the guide
Dishwashers

The dishwasher door suddenly drops instead of lowering gently

A change in door support can make loading unsafe, particularly when a heavy integrated furniture panel is attached.

Read the guide
Dishwashers

The dishwasher door will not latch without being pushed hard

A door that needs force should be checked for loading or alignment problems before further use.

Read the guide
Dishwashers

The dishwasher drains at the start but never begins washing

An initial pump sound followed by silence or a warning is more informative than saying the dishwasher simply will not start.

Read the guide
Dishwashers

The dishwasher filter becomes heavily dirty again after each wash

Repeated filter contamination is worth assessing alongside loading habits, food residue and overall washing performance.

Read the guide
Dishwashers

The dishwasher filter will not sit or lock correctly after cleaning

A filter that does not seat as described should be resolved before the dishwasher is used again.

Read the guide
Dishwashers

The dishwasher is completely blank and unresponsive

A blank control panel needs a power-supply history before anyone can distinguish an appliance fault from a wider electrical problem.

Read the guide
Dishwashers

The dishwasher moves or tips forward when a basket is pulled out

Unexpected movement during loading is a stability problem that should be resolved before the appliance is used normally.

Read the guide
Dishwashers

The dishwasher programme takes much longer than expected

Long duration is not automatically a fault; compare the selected programme and options with the machine’s own published running times.

Read the guide
Dishwashers

The dishwasher salt indicator is lit

A refill indicator should be identified correctly and handled using the model’s salt instructions, rather than treated as a generic fault code.

Read the guide
Dishwashers

The dishwasher seems stuck on its final minute

An estimate that stops counting down should be reported with the machine’s sounds, water level and eventual outcome.

Read the guide
Dishwashers

The dishwasher smells unpleasant after several days without use

An idle machine with food residue needs a different investigation from a machine that returns dirty water after every wash.

Read the guide
Dishwashers

The dishwasher stops halfway through a programme

A pause, a power interruption and an unfinished programme can look alike until the display and water level are considered together.

Read the guide
Dishwashers

The dishwasher suddenly makes a harsh grinding sound

A new harsh sound deserves a stopped appliance and a description of its timing, rather than repeated trials to identify the source.

Read the guide
Dishwashers

The dishwasher tablet is still inside the closed dispenser

A tablet trapped behind the dispenser lid calls for a different check from a tablet that released but failed to dissolve.

Read the guide
Dishwashers

The dishwasher trips the electrical protection during a wash

The stage at which the protection trips is valuable evidence, but deliberately repeating the trip is not a safe diagnostic method.

Read the guide
Dishwashers

The dishwasher will not resume after the door was opened

Resume procedures vary between models, so a paused wash should be handled using the original controls and instructions.

Read the guide
Dishwashers

The integrated dishwasher door catches on the kitchen plinth

Contact with the plinth or furniture front can be an installation problem even when the appliance latch itself works normally.

Read the guide
Dishwashers

The kitchen sink gurgles when the dishwasher empties

A noise at the sink during draining can point the conversation towards the shared waste arrangement rather than washing performance.

Read the guide
Dishwashers

The whole dishwasher load is unexpectedly cold and wet

A new drying problem affecting every material deserves a fuller report than the usual droplets left on lightweight plastic.

Read the guide
Dishwashers

The wrong product was poured into the dishwasher salt reservoir

A reservoir mix-up needs product-specific advice before the appliance is run, rather than an improvised rinse-through.

Read the guide
Dishwashers

Using AEG SprayZone for one heavily soiled pan in a mixed load

SprayZone targets a designated area of the lower basket on equipped models. The pan must be positioned in that area to benefit from the selected option.

Read the guide
Dishwashers

Using Miele Pasta/Paella for dried starch on cookware

The special Pasta/Paella programme in the HG07-W manual includes extended soaking for suitable loads with starchy deposits. It addresses a particular soil type.

Read the guide
Dishwashers

Water appears beneath the dishwasher but the door looks dry

A dry door does not make an under-appliance leak harmless; the source may be hidden behind the fitted kitchen.

Read the guide
Dishwashers

Water collects on the bases of cups and bowls after washing

A small pool in an upward-facing recess can be a loading issue even when the rest of the item has dried.

Read the guide
Dishwashers

Water leaks from the front of the dishwasher door

The first visible escape point and the stage of the wash help an engineer separate a door-area leak from water travelling underneath.

Read the guide
Dishwashers

Water left above the dishwasher filter after a completed wash

A broad pool covering the filter area deserves a different response from a little water hidden in the sump.

Read the guide
Dishwashers

Water marks inside a newly delivered Bosch dishwasher

A few internal water traces can come from factory testing; damage, food residue or missing parts need a different response.

Read the guide
Dishwashers

Why an AEG AirDry door should not be pushed shut immediately

The FFB93807PM manual warns against closing the door within two minutes of automatic opening. Check the exact AirDry timing before reacting to the moving door.

Read the guide

LET’S GET THE DETAILS RIGHT

Tell us what has changed.

Have the model, symptom and postcode ready. We’ll confirm suitable work and availability.

CallBook onlineRepair help